经典福克斯研讨群（群号263416835） 一路走来，收获颇丰，更是认识了很多很真诚的朋友。。。ELM327各种功能不断被挖掘，，现阶段，，经典福克斯群 开始研讨 0303和 0403仪表的rom升级，敬请期待。。。。。

---------------------------2013.10.14

从ELM327开始，，慢慢的，小群变成 经典福克斯研讨群 了，专门讨论经典福克斯各种改装和技术交流。。。。。欢迎加群
ELM CONFIG ，ELM327 福克斯电脑隐藏功能开群研讨，群号263416835 ，加群一起研究吧。。
收集福友的帖子，
ananaizz的 【[DIY]FOCUS达人系统, 你也可以自己搞定速控锁/瞬间油耗/亚洲版油耗单位】
网页链接
vinparadise的 【补上改线图，通杀HS MS CAN】【申精，屌爆了】老福的都看过来，胎压监测
网页链接

copckeke的 【用ELM327可以在老款车上开启另一个09-11的功能】
网页链接

没得资产 的 【开启油耗显示、2.0的胎压检测/ESP开关、超速报警、自动落锁等功能的方法】
网页链接

[ 本帖最后由 jolababa 于 2013-10-14 11:40 编辑 ]

ELM CONFIG 0.1.2.1B版下载   最新版支持rom版本升级，压缩包内带0509版本rom，目前未经测试，切勿盲目升级。
*****
无法运行的补丁
*****
0.1.2.1B版本升级说明
Updated ELMConfig. Version 0.1.2.1b.
Changes:
- Instead of using the command AT SP AT TP, which in theory should extend the life of EEPROM adapter (thanks for the idea ittrium)
- Added ability to change the speed ELM327, to the maximum 500 000 bps, with preliminary testing of the possible rate
- Added the ability to record in the log file
- Added ability to flash module restyling HEC ROM to version 509 (big and small screen)
Notes:
- Read all information messages that appear during the flashing procedure
- Sewn ONLY restaylovye tidy. The type is determined automatically, other types of sewing priborok not give
- For speed (thanks quickie):
1) The adapter should have USB-COM interface chip based FTDI. You can check this: Device Manager => Ports => USB Serial Port => Properties. The "manufacturer" should be "FTDI"
2) Go to Device Manager => Ports => USB Serial Port => Properties => Port Settings. We put here the maximum available speed (top list). Then go to Advanced, and change the value of "Latency Timer (msec)" to "1" (originally there is "16"). OK, OK, close the Device Manager
3) Run ELMConfig. Put the current speed (typically 38400, if before that did not do anything.) Click "Set speed". There, click "Start a test speed test." If all goes well, in the right list set to the maximum speed, which is contrary to the log of the test is "OK", click "Install". Closing ELMConfig. We pull out the adapter from the USB connector and diiagnosticheskogo, then stick the back. After that, when run ELMConfig, in rates should always choose the one which set up the adapter. If you are lucky, and the adapter works by 500,000, it is already the default
[ 本帖最后由 jolababa 于 2012-9-17 01:04 编辑 ]

熄火后的仪表板和音响的灯光熄灭延迟时间，默认10分钟

在GEM-CONFIGURATION-PAGE1
For interior lighting courtesy lights battery saver function 1-255 min: (10)

防盗功能开启（TW同胞开启了），开启后四个方向灯不断闪烁，要有声音的话，要额外加装防盗喇叭。
设置方法：
ELMConfig -> MS-SAN -> GEM -> Configuration -> Page2 ->Alarm System

有高手能把elmconfig的选项都翻译一下么？看不懂啥意思啊

:ns9 ,,嗯嗯,有我的转贴,不会不会,,,  平均油耗都开不了

你确定这一项可以更改？
这一页的内容，我改完write GEM 的时候，跳出N个提示框
重新读取后，数值没有改变

平均油耗或者瞬时油耗目前只有rom版本为0203,0508,0512才能开，0303,0403不行

和仪表盘有关系吗？

为什么我0508的就是开不了,平均油耗呢